RHCE — различия между версиями
Материал из pNp Wiki
Andy (обсуждение | вклад) |
Andy (обсуждение | вклад) (→System configuration and management) |
||
| Строка 17: | Строка 17: | ||
==== System configuration and management ==== | ==== System configuration and management ==== | ||
* [[network_teaming_or_bonding|Use network teaming or bonding to configure aggregated network links between two Red Hat Enterprise Linux systems]] | * [[network_teaming_or_bonding|Use network teaming or bonding to configure aggregated network links between two Red Hat Enterprise Linux systems]] | ||
| − | * Configure IPv6 addresses and perform basic IPv6 troubleshooting | + | * [[Configure IPv6 addresses and perform basic IPv6 troubleshooting]] |
| − | * Route IP traffic and create static routes | + | * [[Route IP traffic and create static routes]] |
| − | * Use firewalld and associated mechanisms such as rich rules, zones and custom rules, to implement packet filtering and configure network address translation (NAT) | + | * [[Use firewalld and associated mechanisms such as rich rules, zones and custom rules, to implement packet filtering and configure network address translation (NAT)]] |
| − | * Configure a system to authenticate using Kerberos | + | * [[Configure a system to authenticate using Kerberos]] |
| − | * Configure a system as either an iSCSI target or initiator that persistently mounts an iSCSI target | + | * [[Configure a system as either an iSCSI target or initiator that persistently mounts an iSCSI target]] |
| − | * Produce and deliver reports on system utilization (processor, memory, disk, and network) | + | * [[Produce and deliver reports on system utilization (processor, memory, disk, and network)]] |
| − | * Use shell scripting to automate system maintenance tasks | + | * [[Use shell scripting to automate system maintenance tasks]] |
| + | |||
==== Network services ==== | ==== Network services ==== | ||
* Network services are an important subset of the exam objectives. RHCE candidates should be capable of meeting the following objectives for each of the network services listed below: | * Network services are an important subset of the exam objectives. RHCE candidates should be capable of meeting the following objectives for each of the network services listed below: | ||
Версия 10:46, 24 ноября 2017
Для подготовки к экзамену использовались следующие материалы:
Видеокурсы Linux Academy
Замечательная книга Сандера Ван Вогта: Sander van Vugt - Red Hat RHCSA/RHCE7 Cert Guide: Red Hat Enterprise Linux 7(EX200 and EX300)
Официальная документация по Red Hat Enterprise Linux 7
Официальная документация для подготовки к экзамену EX300
Сайт с информацией для подготовки к экзамену CertDepot
В данный момент, экзамен носит номер EX300 и включает в себя следующие темы:
System configuration and management
- Use network teaming or bonding to configure aggregated network links between two Red Hat Enterprise Linux systems
- Configure IPv6 addresses and perform basic IPv6 troubleshooting
- Route IP traffic and create static routes
- Use firewalld and associated mechanisms such as rich rules, zones and custom rules, to implement packet filtering and configure network address translation (NAT)
- Configure a system to authenticate using Kerberos
- Configure a system as either an iSCSI target or initiator that persistently mounts an iSCSI target
- Produce and deliver reports on system utilization (processor, memory, disk, and network)
- Use shell scripting to automate system maintenance tasks
Network services
- Network services are an important subset of the exam objectives. RHCE candidates should be capable of meeting the following objectives for each of the network services listed below:
- Install the packages needed to provide the service
- Configure SELinux to support the service
- Use SELinux port labeling to allow services to use non-standard ports
- Configure the service to start when the system is booted
- Configure the service for basic operation
- Configure host-based and user-based security for the service
HTTP/HTTPS
- Configure a virtual host
- Configure access restrictions on directories
- Deploy a basic CGI application
- Configure group-managed content
- Configure TLS security
DNS
- Configure a caching-only name server
- Troubleshoot DNS client issues
NFS
- Provide network shares to specific clients
- Provide network shares suitable for group collaboration
- Use Kerberos to control access to NFS network shares
SMB
- Provide network shares to specific clients
- Provide network shares suitable for group collaboration
SMTP
- Configure a system to forward all email to a central mail server
SSH
- Configure key-based authentication
- Configure additional options described in documentation
NTP
- Synchronize time using other NTP peers
- Database services
- Install and configure MariaDB
- Backup and restore a database
- Create a simple database schema
- Perform simple SQL queries against a database
